various bits for sale

[edmc-monkeyjim]

Hi Guys ,

I have several boxes of parts for sale .
SU carbs all sizes .
Alloy inlets and standard inlet/exhaust manifolds.
Unused pre verto clutch kit , quality make, Borg Beck I think.
Both types of starters .
New LMC pattern bonnet (round nose) in black factory coating but rusty spots from sitting in old garage .
1969 850 engine complete with coil carb etc , the engines alive the bodyshell was dead.
set 12 inch steels with legal tyres.
MK1 front and rear screens ( toughened)
4 cobra 5x10 supaslot alloys with 165 tyres, couple may be legal.
1 BWA 5x10 alloy wheel good condition.
plastic fuse box covers.
plastic and glass indicator lens, type held on with chrome ring.
MK2 wiring loom .1969
MK2 SPEEDO 1969
1960's fuel tank.
Front and rear 1969 mk2 bumpers with overiders. Certainly not mint but someone might want them.
Somewhere I have a pair of mk2 opening quarter lights . Will fit any model except mk1.
Large 80's 90's style distributor shield , no fixings.
Early 80's Mayfair grey velour front seats.
Various types of distributor from mk1 on .
Pair of aftermarket front seat frames.
Spacered rear drums .
Several heads all standard. 1 is MG A+ with valves but not fitted another is Maestro 1275 A+ fully assembled , possibly unleaded not 100% sure regardless of that it still fits a Mini.
MK2 rear lights
Grey 1969 mk2 vinyl seats.
Headlamp chrome rings ,
Metro air filter cases, drill holes in it and uprate the standard set up.
850 metal air filter cases
Grilles
Van estate rear door repair bottom inner and outer sections, need to check whether left or right. light surface rust.

Pair of brand new clear perspex fixed quarter light windows, fit mk3 onwards. Made by plastics 4 performance who supply the Mini 7 and Miglia racers with windows.

MK3 distributor shield, small type fits behind grille.
black 13inch 3 spoke steering wheel, black spokes with round holes.
Plus loads and loads of other bits and bobs from early 60's up to early 90's. Loads of bits from a 1969 saloon.To be honest I cannot remember what I have got so let me know what you want and i will have a rumage. cheap.


Unfortunately I have no discs brake set ups, 1275 engines I am willing to sell or wheel types other than what is mentioned above.No panels other than above items mk3 doors.
All parts located in Peacehaven. Can be collected from Fairlight garage in Saltdean.
Must go now , just found out the Italian job is on a sky channel, there just about to load the Coopers with gold .
Cheers Dave
www.edmceventsco-ordinator@fsmail.net
Fairlight Garage 01273 303020 .

ALSO: Used Studio 2 boot lid and bonnet with bonnet stay just taken off my Studio2.Painted limited edition Mini Neon/Studio2 Nordic blue metallic £10 and £15.
Brand new Minispares mk1 Austin wavy grille, they cost over £58.00 plus post (see minispares ads to confirm) want £45.00.

[bryn]

hey mate
do you have a passenger side front wing for a mini mayfair?
thanks
BRYN

[bryn]

or a bonnet for mini mayfair

[Michelle]

How much did you want for the perspex rear quarter windows? I was thinking of putting them in my fibreglass Minus project. Are they A1 condition? Are you going to this autotest this PM? Pat

[clubman brown]

Unfortunately I have no discs brake set ups, 1275 engines I am willing to sell or wheel types other than what is mentioned above.No panels other than above items mk3 doors
bryn, it's really not worth getting second hand panels!!!

[bernadillo]

got any decent grilles?

[bryn]

bryn, it's really not worth getting second hand panels!!!

surely second hand is better than none at all??

[clubman brown]

maybe but possibly not!

[bernadillo]

would the "Unused pre verto clutch kit" fit into a metro engine????

im not sure what a pre verto clutch is?

and would the "Maestro 1275 A+ head" make much diffrence from a standard one?

[miniman]

i think that a plus engines are verto clutches and non verto are on the older minis

[STEALTH GT]

IT CAN ALL BE SWAPPED ABOUT ,BUT YOU NEED TO DECIDE WETHER YOUR GOING FOR VERTO OR NON-VERTO IT CANT BE A MIXTURE OF THE TWO.

[edmc-monkeyjim]

Hi guys .
To answer all questions ,

Pat ......Barbara has the perspex windows .

Bryn ...I have no second hand panels.. Yes I have, got a boot lid and bonnet just taken off my Studio 2 . Painted original colour of Nordic blue Mettalic. Bonnet in reasonable condition with bonnet stay £15. Boot lid £10 light rust on part of inner bottom edge only seen when lid open . Will shot blast ok. Respraying the car this week with the aim of showing it , using new bonnet and bootlid .

The new pattern, slightly rusty bonnet is now sold.

Bernadillo...For arguments sake and without looking it up to be 100% take it that all Metros and Minis from 1982 I think are all verto. Although I may be wrong. Please advise If you know differant. They cannot be mixed and matched. The starters are also differant .

...The Maestro head will fit a 1275 Mini or Metro. If fitting to a 998 the block will need machining to except the head.
Regarding the performance potential of the A series Maestro head I have not measured the valves to see what size they are . Would guess they are mg size giving the thing a bit more go to lug the bigger Maestro body around Have a look in David Vizards Tuning the A Series big yellow book . Sure its got standard valve sizes in there for all A Series vehicle applications.

Other than a spare I am keeping I only have a used Cooper grille currently attatched to my pick up . I cannot get at it due to building materials pinning front of pick up close to a wall in garage . Will be moving pick up next week . Will see if you still want it by then .
I do have a brand new Minispares mk1 wavy grille. Cost £58.70 plus post, see Minispares ads to confirm. Want £45.

Thanks for you enquiries .

Dave

PS: Stephen from EDMC wants a standard 7.5 gallon fuel tank. Its the larger size fuel tank fitted from 1974. Anyone? See edmc forum wanted section .

[Michelle]

Dave, Pat says thanks for the windows. Very interested in the wavy mk1 grille, do you know if it's chromed or galvanised? You don't have the surround as well do you?

[bernadillo]

how much do u want for the clutch? i havent put the metro engine in yet so the clutch is accessable, ive decided to get a new one because i dont know what condition the current one is in, if it is easy to switch to a "pre verto" and u have a good offer on the clutch then i will go for it...is there a diffence in performance between the verto and non verto? and will any other parts be needed to switch?

also...do u have a drivers door in good condition?

also...how much is the Maestro head going for?

[edmc-monkeyjim]

Michelle the grill is stainless I believe . I do not have a surround . Best quality at best price for the surround would be from the minispares stand at London to Brighton.
Dave

[edmc-monkeyjim]

to be honest its a bit of messing about ( easy messing about) swapping from verto to pre verto just to save a few quid on the clutch.
You will need the pre verto slave cylinder, clutch release arm , plunger , clutch and possibly the flywheel . If you change the flywheel you will need to make sure the flywheel ring gear has 129 teeth , otherwise you will need to fit the earlier starter motor as well. If you do not the starter will jam up . Found that out the hard way , lol.
Will have a good look thursday see if i have a verto kit.
Both the clutch kit and head are £25 each .
Apologies if I do not get back to you for a few days as will be on Riviera Run, back tuesday.
Dave

[Michelle]

OK Dave - will you take £40 for it?

[edmc-monkeyjim]

i would like £45,
Dave

[edmc-monkeyjim]

4 steel 4.5x12 inch wheels from 1990 studio 2 with legal 145/70/12 tyres.
£20 the lot

[Dr Dave]

There is also quite a big difference in price of new clutch kits , non verto are far cheaper.